Replaced garage door in private house

Garage Door Replacement: Cost Vs Value

The first step in replacing a garage door is seeking a professional opinion. With an expert view, you will be more enlightened about the requirements. Professional consultation is also an essential step in establishing the cost implications. It also allows you to interact with available designs for enhanced aesthetics.

Replaced garage door in private house

Apart from expert advice, there are several factors that you should consider. These factors usually have cost implications on door replacements.

Number of openings

The number of openings for your garage door determines the costs you will incur upon deciding to replace them. There are garage doors with one, two, or three openings.

Size of the door

The second factor you should consider is the size of the door. What are the measurements? What is the measurement of the width and the height of the door?


The third factor you should consider is the material used in the manufacture of the door. In most instances, steel doors have the highest value in the market. This is because they tend to be more durable and secure. Wooden doors are equally expensive and must be maintained periodically. However, fiberglass doors tend to be cheaper.


The color you decide on also has cost implications on the cost of the door. In most instances, doors are white. This means that if you opt for a different color, then there is the likelihood of an increase in the total cost of the door.


In some instances, doors come with windows. The style used in making the windows and their number impacts on the total cost. The total cost of door replacement is also dependent on the type of glass used.


Another crucial factor worth considering is the thickness of the door and its insulation. Different climatic regions require different levels of insulation. For harsh weather, you will need a thicker door. This implies that you will have to dig deeper into your pocket.


Lastly, there is always the desire to customize doors to specifications of the owner. You would want this for your garage door. For the increased appeal, you will have to dig deeper into your pocket.

For proper planning, you will need a quote. This can be obtained from a garage door professional. Ensure that you bring the expert to the site to inspect the door. It is during this time that the measurements of the doors are taken. At this moment, any other damages that require repairs before installation are noted. The materials to be used are discussed together with the intended style. The quotation is determined at this point. A contract is then signed.

From the discussion, it is clear that for the best value, the cost of door replacement is high. The best value doors are manufactured from the best material. The color of the door, the quality of windows, and the customization for best aesthetic outcomes depend on the depth of your pocket as the owner of the garage door. The value of the garage door is also determined by insulation, which also depends on the budget.

White garage doors and the car

How to repair garage door panel

Door panels are usually joined together in the tracks to allow the garage door to move freely up and down. Whenever damage occurs, it most likely emanates from the tightening of the bolt or rust. The damage can also be a dent, misuse, or as always, the door has served for a long time. The latter makes the door weak and due for replacement. Adequate door replacement can be achieved by choosing the right door repair company. The company should also have an experienced workforce. Some of the considerations that should be made include the appearance of the previous door. This helps in ensuring that the door does not deviate from the previous model.

White garage doors and the car

While repairing the garage door panel, you should seek advice on the latest repair methods and materials from the experts. Alternatively, you should hire professionals. They are more familiar and experienced with the task. Below are a few things the expert has to follow for the task to be accomplished.

Order the panel

After determining the type of the panel and its model, the technician should order the panel that has the feature of the damaged one. This step is imperative because it ensures that the door fits well. The market is also awash with suitable alternatives. This helps a great deal when the previously used panel cannot be found in the market. However, if a similar panel is not in the market, then the manufacturer should be consulted to help out.

Remove the panel

While removing the old panel, the technician should be keen on the task. The technician should be cautious not to break the new panel. In the process, the garage door has to be opened manually, and the springs removed slowly. In the cases of automatic garage door openers, they should be unplugged before the new fittings are done. This has to be done since it can lock the technician inside and cause the injuries and damage the new panel. However, some garage door panels are placed at the top; hence when the repair has to be done; then the other panels have to be removed step by step until the damaged one is located.

Replace the panel

The new panel is placed on the roller then lowered until it reaches the panel below. The panel should be attached to the immediate one by the use of either screws or bolts. This depends on the type of garage door. Ensure the panels are orderly retained in their original place. Confirm if all the springs are in their respective holes. Remember that the door opener was removed. After all the fittings are done, the garage door opener should be reinstalled and tested. Make sure the repaired panel retains its original place. Confirm if the fittings are in their rightful place by checking if the door panel moves up and down easily.


After all the replacements are done, the door panels might look different in color. The best way to go about this is to repaint the whole garage door panel.

Wooden garage doors

How to Repair Liftmaster Garage Door

Imagine getting home when it’s raining, and you have to get your car into the garage. As usual, garage doors are heavy. This makes opening and closing them manually, quite a task. In circumstances like the one mentioned, Liftmaster garage doors come in handy. With such doors, the opening and closing of the doors are automated. With the help of a chain, belt, or screws, Liftmaster doors are more comfortable to open and close. However, just like any other doors, Liftmaster has several issues. The good news is that the manufacturer understands this. As such, the manufacturer has identified the most likely problems with Liftmaster and presents several possible solutions. From the instructions, you can fix most of these issues on your own.

Wooden garage doors

Safety Sensors Hitches

There are instances in which the door might not close. Alternatively, it could be closing partly and reopening immediately. In such cases, the first step in such a scenario id to check out the safety sensors. Usually, this results from a material blocking light between the sensors. This is simple. Just clean the lenses. There is also the possibility of cobwebs engulfing the door tracks. They are also possible to light detractors. Removing them solves the problem altogether. There are also instances that you will note some light blinking from one sensor. This indicates an alignment issue. You can correct this by adjusting the light until it shines without blanking. Another possible cause of sensors’ misalignment could be loose door tracks. This is simple, tighten the bolts.

Close/Open Hitches

Most of the functions of the Liftmaster are programmable using the remote control. If by chance, the door is not opening or closing appropriately, you can reset the capabilities of these functions. This can also be done manually using the limit dials.

Faulty Remote

For new Liftmaster door openers, the remote hardly works until it is programmed. The manufacturer provides a manual that is essential for programming. There are also instances that the remote suddenly stops working. Often, this is caused by used-up batteries. Replace the batteries.

Error Codes

Whenever you purchase a Liftmaster garage door opener, you will notice that it has an error code system. This is made up of several flashing lights. This can be solved quickly. The user manual will direct you on how to decipher the error. As such, it is essential always to keep the user manual. However, if you happen to lose the user manual, then you can access it on the Liftmaster website.

Power Issues

Another common issue with Liftmaster garage door openers is power source problems. This is very easy to find out. When your garage door is not binding when the springs are functioning normally, then you can repair this on your own. You should first check out the source of power. Ensure that the opener is plugged into a functioning outlet. Another possibility could be that the cord is damaged or just disconnected from power. You should also ensure that the circuit breaker is open. With these steps, you will be able to diagnose and address any power issue that might be bedeviling your Liftmaster garage door.

Wooden brown garage door

Why do your garage door squeak

According to experts, garage doors are not expected to be quiet. However, when they become too squeaky, they can easily annoy. This can be a constant source of disturbance to everyone within your compound and even within the neighborhood in extreme cases. When this happens, the most effective step to take is to consult a door repair technician. From experience, these professionals can quickly diagnose what could be ailing your door. Over the years, several factors have been identified as possible causes of squeaking.

Wooden brown garage door

Rusty Parts

Rusting tends to be a common source of squeaking in most faulty doors. When rust strikes the bolts and the hinges, the result is visible. The doors suddenly become tight and sticky when opening or closing. This should be an alarm loud enough to tell you that there is a problem that needs to be tackled. Various degrees of damage call for different measures. If the rust has resulted in the tear and wear of the door, then the replacement of parts or the door, in general, is always advisable. However, if the squeakiness is not that severe, then you need to apply lubricants or spray the affected parts with non-wax lubricants. This will help address the problem.


This is usually blamed on incorrect installation. When garage doors are not correctly installed, parts keep rubbing on each other, resulting in noise. It can also result from wear and tear of mounting components such as hinges or the rollers and tracks. You can install the worn-out parts or replace the door.

Faulty Rollers

After long term use, rollers are likely to get loose. When this happens, you will experience difficulties when moving the door up and down. Faulty rollers also result in the metal to metal friction. Loose rollers can be fixed by screwing in the rollers back into position. Alternatively, the rollers can be replaced. For the best results, it is essential to source for the manufacturer’s approved parts for your garage door.

Faulty Chains

Chain drivers are usually the loudest when dry. However, this can be corrected by applying the recommended lubricants. This makes them move freely, leading to the elimination of the squeakiness. Squeakiness from chains is also caused by missing or broken links in the chain. The best strategy in such a scenario is replacing the chains. Another possibility could be the tightness of the chain resulting in squeakiness. You can correct this by making necessary adjustments.


Broken track

One of the integral parts of a sliding door is the tracks. When they are not handled carefully, they tend to break. On breaking, the garage door becomes squeaky when opening or closing the door. In such instances, it is usually advisable to contact an expert owing to the complexities involved in track replacement.


In some instances, garage doors, just like any other exit door, are exposed to debris. These include dried leaves and dust. For sliding garage doors, when this debris falls into the tracks, one obvious result is friction. This results in squeakiness as the debris prevents the door from opening and closing smoothly. This can be prevented by cleaning the door regularly.

Try these methods out for the best results when experiencing squeakiness with your garage doors.

Grey insulated garage door

How to repair garage door spring

For purposes of repairing a garage door spring, there are two main stages you must put into consideration, first of all, being the removal of the old spring and then installing a new spring.

Grey insulated garage door

Removing the old spring

  • First of all, remove the door opener’s plug and then clamp the track and the door together to prevent the door from opening on the release of the spring.
  • Hold each spring using a winding bar while loosening the set screws. For safety purposes, have the sturdy ladder positioned to the springs’ side.
  • Using two winding bars, unwind each spring, positioning into a hole on the cone, the second winding bar perpendicular to the first one.
  • Make the springs slide up to the end bracket after removing the bolts as well as the nuts.
  • Put the torsions’ tube in a secure position preventing it from moving and then untighten the set screws on the lift cable drums using a wretch. Make the cable drums and springs slide off the torsion tube after disconnecting the lift cables.
  • Take the measurements of the length of the spring when it is still relaxed since having the measurements when it is installed may be inaccurate due to the existing tension on them. The measurements should be taken in inches for purposes of ordering replacements. Ensure that the spring you are measuring is not broken.
  • Use a tape measure to determine the diameter size of the spring as well as the size of one coil, which is gotten by dividing the total length of the coils by the number of coils.
  • Make orders for replacement springs online since it is difficult to have them from manufacturers and distributors if you are not a professional. Ensure what you are ordering is compatible with the measurements of your spring because any slight difference can cost you another order.
  • Ensure you make any necessary replacements before installing new springs to avoid dismantling the door again and starting from zero.

Installation of new springs

  • Insert the left spring into place on the torsion tube and then have the bar inserted into the left bracket after replacing the cable drum.
  • Install the spring on the right as well as the bearing at the center and then have the bearing pressed into the cones at their stationary point.
  • Fix the cables and make the drums tight.
  • Following the supplier’s recommendation, wind the springs.
  • Stretch out the springs from the center by tapping the winding bar using a hammer
  • Tighten each set screw until they contact the tube. Do not make them too tight because this may distort the tube.
  • Use a garage door in lubricating the springs on both sides and ensure the excess is wiped off.
  • You can now safely remove the tools you used in holding the bar and the garage door, which may be pliers or even clamps.
  • The final step is to check if the garage door is now properly working. You just lift the door high about 1m and let it go. If it does not go down, then you can now have the opener plugged back, but if not, add another turn to each spring.
Repaired insulated garage doors

Top three reasons to hire a garage door repair service

Most of the time, when someone’s machine encounters a technical malfunction, the owner first tries to check if they can repair the damage, even if they lack knowledge on the machine’s hardware or software. The case also applies to some when it comes to garage doors, and this may even cause a bigger problem than the one you already have.

Repaired insulated garage doors

This, therefore, makes it preferable to hire a garage door specialist to check on the damage and do the repairs. These doors are technical in nature, and even a slight mishandling can cost you the whole garage door, and even in some cases, you find that someone got seriously hurt by some parts of the garage door when trying to do the repairs. A garage door repair service is therefore recommended due to the following good reasons:

Having your garage door repaired in the correct and more assuring way

Having a specialist to repair your garage makes you comfortable when he or she is at work because you are sure that what is being done is the right thing. The specialists are well trained and equipped with the relevant knowledge concerning every single detail of your garage door. When there is a problem somewhere, they can’t fail to notice it and take the relevant approach. The specialists have the various equipment needed for the repairs and even new spare parts for the garage. In case any of the parts of the garage are worn out or something of that kind, your garage will be well serviced. The cost of hiring a garage door repair service should not bother you, considering the service done to your garage. You would really appreciate how it was worth it, giving out your cash.

Your safety as the owner

Hiring a garage door repair specialist saves you from risking your life by exposing yourself to the technical and delicate components of the garage door. When you do the repairs yourself, you may end up getting yourself bruised by the parts of the garage door, such as the tracks and hinges, which are very dangerous. The size of the spring and the amount of energy that a slipped spring develops is too much that it can cause very serious damage to you. The specialists are well conversant with the delicate parts since they have been exposed too much on them due to the frequent repairs that they do, and so they cannot have a problem in fixing the parts.

Warranty of the garage door

In case your garage door is repaired by a specialist, then you will have a warranty and be assured that the repairs done would make it last longer before requiring any repairs. The warranty covering your garage door is more advantageous since in case there is any malfunction within the period of warranty then repairs would be done without you giving out even a single penny.

New insulated garage doors

Easy garage door inspection

As a garage door owner, you need to do an inspection as regularly as possible. This helps you to notice whenever there is a problem with your garage door and solve it immediately.

New insulated garage doors

The following could give you guidance on how to carry out an inspection:

  1. Confirm that the door has its weight uniformly distributed and that none of the sides is weightier than the other, because this may cause difficulties while opening the garage door.
  2. Check whether the emergency release cord is functioning well. Try pulling it to check whether it can let the door free for manual operation.
  3. Check on the extension springs and try if they are worn out and need replacement. In case any is broken, do not attempt operating the door until the replacements are done.
  4. Check whether the torsion springs are well attached to the torsion tube and, if not, contact a technician and do not operate the door yet because this will interfere with the normal operation of the door.
  5. Check if the door bearings are well pressed onto the cones and also check whether they have cracks or they are wearing out.
  6. Also, check whether the torsion rod has warped or whether there are any signs of wear on them.
  7. Ensure the cables are well connected and their drums tightened as well.
  8. Confirm that no cable is fraying and that they are all in good condition.
  9. Check for any signs of wear on the pulleys and, if any, make necessary arrangements to contact a technician.
  10. Confirm whether the track can clamp and unclamp with the door without any obstruction and ensure there is an alignment.
  11. Confirm that the rollers have no crack and that the door is sliding up and down smoothly without any hindrance.
  12. Check whether the weather seals are worn out or need replacement.
  13. Check whether the struts are in good condition.
  14. Confirm that the hinges are not broken and that there is no weight bias in any of the sides for purposes of preventing any further crisis.
  15. Check whether any garage door panel is sagging or whether there are any cracks.
  16. Check whether the sensor’s eye is clean because the signal that turns the motor will be blocked, in case it is dusty.
  17. Confirm whether the chain is properly placed, and if it is broken or loose, then it needs to be repaired by a technician.
  18. Plug and unplug the door opener to check if it is properly functioning.
  19. Confirm that the trolley is running smoothly without any distractions.
  20. Confirm whether the opening and closing of the door are consistent when switched on and off.
  21. Test whether the remote control is functioning and also check the batteries well in case there could be a need for any replacements.
  22. Confirm that the brackets are secure and tightened properly.
  23. Confirm that the bolts are well tightened and that none is loose.
Closed insulated garage doors

How to repair garage door opener

To you, a garage door opener may appear technical to repair in case of malfunctions. After reading the article below, you will realize that you no longer need a technician to some extent, to do the repairs for your garage door opener.

Closed insulated garage doors

These are the steps involved:

  1. You can start by checking the plug and confirming if into the working outlet the opener’s cord is plugged because it is also one of the factors which can cause the garage door not to open.
  2. Check if the garage door lock has been activated. This is because, in some cases, you may find that it had been locked by the owner and thereafter not remembered to inactivate it. Many people, however, fail to think of that as a cause of the malfunctioning.
  3. Test the garage door opener several times by plugging it in and out repeated times since, at times; this may help to reset the sensor.
  4. Sometimes the problem may even be with the batteries of the remote control opener, either damaged or not well inserted and not the garage door opener itself and so you can check on them and buy new batteries if necessary.
  5. Check on your remote. It might be the problem that is disabling the garage door from opening. In this case, you can do reprogramming of the remote using the tips clearly outlined in the owner’s manual.
  6. Confirm whether the plugging in of the beam sensor is done correctly and, if not, do so.
  7. Using a wet cloth cleans the sensor’s eye since by being dirty, it prevents the motor from accessing signal making it unable to turn on. The sensor is found in front of the on and off button on the remote control. Regular cleaning of the sensor minimizes problems.
  8. Confirm whether the chain is loose or broken and if so, then it needs to be repaired and therefore, may need the attention of an electrician.
  9. In case all the attempts so far fail to work, then you can operate it manually. In most cases, a red release cord may be pulled to let the door free for manual opening and closing. For older systems, however, the case may be different. Instead of the red release, there could be a handle that is pulled down or even a spring-loaded clip. It can also be done by removing the bolts on the arm between the opener and the door to loosen them.
  10. The final step now, which turns out to be the only option left is to seek assistance by either contacting the department of services of the place where you purchased the garage door unit or contacting an electrician.

What you need

  • Owner’s manual
  • Batteries for the remote control
  • Optical electrician
  • A wet cloth
Three brown garage doors

Tips For Replacing A Garage Door

Garage doors are among the most frequently used doors in a home, although neglected most of the time, therefore, making it very unsafe. Being used most of the time, a garage door begins to wear and tear. Garage doors weigh almost 400 pounds, and therefore replacing it is not that simple. It is a task that requires precaution to avoid unnecessary accidents. If you are not familiar with mechanical equipment, then you should get a professional to handle this matter. You have to take note of these tips if you want to have a smooth garage door replacement process.

Three brown garage doors

  1. The installation of a garage door is not a one-person job unless you have experience in doing so. It is better to get someone to help you to avoid getting hurt. The door is very heavy, and if it falls on you, the results will be catastrophic. The installation of garage doors results in over 1600 injuries every year. Having someone help you is, therefore, the best option to reduce the risks of getting injured.
  2. Install only quality components to your garage door. The higher the quality of the components, the safer the operation of the garage door will be. Install heavy-duty hinges and rollers with ball bearings with many struts for better floor reinforcement. This will increase the life span of its system. Springs of high quality will contribute to a safer operation.
  3. When replacing the garage doors system, make sure that you also replace the track as well. Keeping the old tracks may save you some money but will reduce your level of safety when operating the garage door. The old track may also not fit properly with the new garage door system and also affect its performance and life span.
  4. Install pinch-resistant joints on your garage door. Your fingers may be pinched or crushed when caught in between the joints of the sections. Pinch resistant joints will add to your safety in the operation of the door.
  5. Install brackets that are resistant to being tampered with. The brackets are usually placed under the garage door and experience high levels of tension. It will be very dangerous if a person with no training attempts to tighten or loosen the brackets. Their manufacturers, therefore, added hardware to make them resistant to tampering and they can only be adjusted by a professional with the manufacturers recommended tool for the job,
  6. Lubricate the nuts and bolts and ensure that they are in place. This helps in reducing the noise coming from the door. It also reduces friction and makes the moving parts of the garage door last longer. The garage door will be more stable, as well.
  7. Carry out safety maintenance once in a while if you suspect that there are some issues with the garage door. Has it checked annually to ensure that you have not overlooked any issues? Lastly, remember to keep the garage door clean after replacement. This removes the dirt and grease and ensures that the tracks are smooth.
Electric garage door

How to operate your garage door when the power is out?

For electric garage door users, there is nothing as bad as power going out, and you want to open your garage door, and you are stuck because you don’t know how to operate it without power. Fortunately, some garage doors can actually be used without power; it is quite simple. Using a bypass that electric and automatic garage doors have, you can be able to open the garage door manually. This can also help if you lose your remote. This bypass will disconnect the door from the power-consuming carriage, but it still functions even after the disconnection. When power comes back on, you can lock the bypass and be able to use the garage door normally again. Get a ladder and place it under the chain operating the garage door. Look for a red cable hanging from the chains bracket. The cord should have a plastic knob that is red in color.

Electric garage door

Use the knob to jerk the knob. The cable is connected with a small lever. Pull the cable until the lever locks in a down position. Climb down from the ladder after this, get a hold of the garage door with both of your hands and pull up. If the door does not move, then you will have to pull the cable harder until it unlocks. The door may be too heavy for you to lift on our own, so you should get some assistance if necessary. Once the door has been lifted off the ground, do not let go under any circumstances. In this state, it is free on the track, and it will fall down if you let go. Let someone hold it open for you while you drive your car either in or out. Better yet, you can find something strong to hold it in place. When done with the door, bring it down carefully with your hands.

Pull the cable hard again to lock it in position after the power comes back online. Pull the cable and observe as the bracket slips right back into the chain bracket, which locks the door in power mode. Try opening the door using the remote, and if it does not open but the chain moves, then pull the chain again until the bracket is locked. Test it again and pull cable again if it is required to lock it.

An important tip

Always keep the chains and the rollers of your garage door lubricated. This enables the door to move quietly, and the moving parts and its chain will last longer as friction is greatly reduced. Remember to check your manual before making any changes to your door.

For your safety, never pull the bypass cable if the garage door is stuck in an open position. The door will slide down with great force enough to destroy anything in its path. The garage door is dangerous if precaution is not taken while using them, so be careful in the process.